It is possible to get a water purifier for 4 to 5 years, but you need to take good care of it. There are common problems with your water purifier that you will have to deal with after that. There are many water purifier problems, not just one of them is water leakage. Several other problems may develop after a couple of years of water purifier usage, including unusual taste, noisy faucet, unusual smell, and slow water output. In the following paragraphs, we’ve listed the five most common water purifier issues and their solutions, so you can quickly identify the problem and have it fixed.
Five Most common Water Purifier Problems and Their Solutions UV and RO water purifiers are the most commonly discovered water purifiers in many homes. Each of them could have several issues. Nevertheless, we have compiled a list of the top 5 water purifier issues and attempted to list their specific solutions by infinity hot water.
1. If The Water Purifier Has An Unusual Taste Or Smell
It may be because a biofilm has been Acquired in one Part of the Unit Biofilm is a layer of inorganic and organic material collected by the water purifier. This causes the water to have higher levels of contaminants. The fastest way to deal with this situation is to replace the membrane or any clogged filters. You can see if the water tastes better or if the membrane and filters are changed. Make sure that the filters are replaced every 12 months or so.
In their mechanism, RO purifiers utilize copper tubing. If the water has a metallic taste, it implies that the copper tubing has dispersed many bicarbonates, chloride, and sulfate, which leaves a metallic taste. If the water comes out slightly salty, the salt and other particles in the cleaner have dissolved. To get rid of these contaminants from the water, the RO water purifier must be fully functional. If your cleaner’s water starts to taste salty, it’s a good idea to have it cleaned by a professional to have it cleaned properly. You need to carry out this process once every six months.
2. Slow Water Flow From The Water Purifier
In case your drinking water purifier releases purified water very slowly and fills only half the glass simultaneously, you often have low volume or low water pressure. To properly operate an RO, it requires a minimum pressure of 40 to 60 PSI (pounds per square inch). The cleaner’s water storage tank could be faulty, or the filter could be leaking. The air bladder releases water quickly from the cleaner’s water storage tank because it has an air bladder. The more water there is, the higher the pressure will be.
Any bladder leakage can result in slow water flow from the cleaner due to a lack of pressure in the bladder. The cartridges of the water filter could be clogged up with sediment, which would cause slow water flow. If the filters become clogged, a qualified water purifier technician can help you get them replaced.
3. Making Strange Noises With Your Water Purifier
If the Faucet on your unit Is leaking air, it Is a sign that something Is wrong with the filter or membrane. Changes in the water pressure inside the system could also cause this. If the noise does not lessen after you replace the filter, it’s good to have a professional inspect the tubing to ensure it was correctly installed. If the water tank valve isn’t closed correctly, the noise could also be heard.
4. If The Purifier Faucet Or Filter / Membrane Is Leaking Water
A component of the cleaner is not Fitting correctly. To correct the problem, the ill-fitted part needs to be either replaced or fitted more securely. When the same issue is discovered in the water purifier’s membrane or filter, it might be because of a worn-out O-ring. O- rings are made of a soft rubber that keeps water from leaking into the parts that are being repaired.
If the water purifier is leaking water from the faucet, membrane, or filter, it is good to have a service engineer check the O-rings and ensure the valve is closed correctly. If the O- rings are cracked or are in poor shape, they need to be replaced immediately.
5. Ro Water Tank Doesn’t Fill Up
Another common issue discovered in many UV and RO water purifiers is that the water storage tank does not fill up. The cleaner has external water pressure, which causes the problem. TO FUNCTION PROPERLY, an RO water purifier will have to obtain a minimum pressure of 40 to 60 PSI (pounds Per Square Inch). You will need to get a water pump to help you increase the pressure if your water pressure is under 40 PSI.
The water tank may not be filled up entirely due to a damaged RO membrane. The semipermeable RO membrane forms a barrier that enables only water molecules to get through to the other side while blocking the passage of water contaminants such as dirt, dust, viruses, and bacteria, thus providing a safe and clean drinking water source. The water filtration process slows down when the membrane gets blocked after a couple of months of use, and the water quality degrades. If the membrane becomes damaged or clogged, it must be replaced immediately to prevent any further damage to the membrane.
Depending on the water purifier use, the RO membrane needs to be replaced every year. This will make sure your water is both clean and healthy to drink.
